How to Turn off Seatbelt Alarm (Expert Guide)

Do you want to know how to turn off seatbelt alarm in your car? if so, you are on the right page.

The need to fasten one’s seat belt each time we drive is no longer strange to people. On the other hand, the annoying problem is how to disregard the unpleasant rings and sounds emanating from the alarm.

Fortunately, these incessant rings and sounds can be eliminated, as it doesn’t take much to learn How to turn off seatbelt alarm.

To disable the seatbelt alarm, one great method is to reprogram the computer. Reprogramming the alarm is relatively easy; this can be done by reading the user manual and adhering to the instructions. Setting up a safety belt alarm stopper is another great method.

There are some simple procedures one has to follow to reprogram the seatbelt’s alarm and set up an alarm stopper. Stop that annoying seat belt beeps by studying the guidelines in this article.

How to Turn Off Seatbelt Alarm

Reprogramming or installing a seatbelt stopper are the two major methods of turning off the alarm of the seatbelt; these two procedures will now be further elaborated on.

Method 1: Reprogramming the Seat Belt Alarm With Your Car’s Owner Manual.

Here are the steps to follow to turn off your seat belt alarm by reprogramming the  alarm

1. Beware of the Airbag Risk

to trigger the vehicle’s airbag, many manufacturers configure the seatbelt’s sensor. It is, therefore, necessary to find out if this applies to the car before going ahead to do anything, as tampering with the seatbelt sensor can affect airbag performance.

2. Check the User Manual or Ask Your Dealer to Disable It per Software

The guideline stating how to turn off a seatbelt’s alarm without touching wires is provided in the majority of user manuals. Mostly these are done by following some acts while the ignition is off. For instance, below is the series of steps to disable the safety belt’s warning of a 2014 Toyota Camry, including newer models.

Turn on the ignition by inserting the key without powering on the engine.

Go to the dash panel, and find a knob that switches between the total odometer and trip readings. The knob should be pressed till “ODO” appears on the panel. The key should be switched off and on.

Keep pressing the knob for like 10-15 seconds. Put on the seatbelt while pressing the knob and let go of the knob.

The indication that you have disabled the seat belt alarm will manifest when the “B OFF” flashes on the instrument panel.

3. Turn off the Alarm

This, as stated above, can be done when the vehicle is being parked by following the guidelines on the user’s manual to reset the seat belt alarm. Equally, as with some cars, the seat belt alarm could be modified with a particular software when the car is taken to the car vendor.

The safest way of turning off the alarm is by taking the car to the dealer for him to do that, as he will make logical alterations when faced with peculiar instances. It’s worth bearing in mind that most car vendors hesitate to engage in such services because of the fear of being held responsible for accidents by the laws.

Also Read: How to Open a Trunk Without a Key (Expert Guide)

Method 2: Install a Seat Belt Alarm Stopper

How to Turn off Seatbelt Alarm

The Unattached seat belt clip and the extender are the two types of seat belt stoppers. The various items needed to install the seat belt stopper are;

  • User’s Manual
  • Electrical Tape or Heat Shrink Tape
  • Seat Belt Alarm Stopper
  • Extender
  • Wire Cutters and strippers
  • Software Update (assuming its needed/present)
  • Torchlight
  • Drill alongside Torx Bit or Screwdriver

1. Installing The Detachable Seat Belt Hook

  • The main thing to hook into the safety belt’s opening is an unattached seat belt clip.
  • If you have no plans of making use of the safety belt, then getting an unattached seat belt hook is ideal.
  • This can be bought from an automobile shop or scrapyard; one just needs to ensure that the hook can accurately fit into the vehicle’s seatbelt.
  • To ensure it will fit, the entire seat belt clip’s exposed metal column size should be examined and compared to the safety belt opening.
  • If you plan to make use of the safety belt, then you can purchase an extender.

2. Installing The Extender

The other primary option for stopping the unpleasant sounds is the extender, which can be purchased from a good part producer.

An extender is a part clasp unto the seat belt’s port. It comprises an additional port so the user can still use the seat belt even when the alarm stopper has not been removed.

There is a need to determine if the requirements on your seatbelt producer’s website match that of the extender because of the great importance of purchasing a genuine extender that fits. The importance lies in ensuring that the seatbelt system can sustain the anchorage pull test, which ensures that the system can subdue crash-level thrust.

Fasten it once you ascertain that the extender can clasp into the seatbelt opening. The unpleasant beeping should consequently stop.

Also Read: How to Bypass Reduced Engine Power (Step by Step)

How to Turn Off Seatbelt Alarm on a Dodge Ram

How to Turn Off Seatbelt Alarm on a Dodge Ram

The Dodge Ram possesses sensors in both the driver’s and front passenger’s seats to prompt users to fasten their seatbelts. It chimes until the users fasten their seatbelts. The Dodge Ram seatbelt alarm is known as the “Belt Alert.”

Step 1: Get in the car and close the entire doors first.

Step 2: Turn on the ignition by putting in the key and fastening the seatbelt. You shouldn’t start the car engine; rather, just switch the access to the “on” point. Wait for the seatbelt indicator to go off before proceeding to the next step.

Step 3: Note you should not power on the engine yet; simply hook and unhook the seatbelt thrice in less than a minute of switching the car on. The seatbelt should then be hooked for one last time.

When you twist the key to the lock point, the seatbelt alarm will beep one more time. This beep indicates that the belt alarm of the Dodge Ram has been successfully turned off.

How to Turn Off Seatbelt Alarm on Subaru

  1. To disable your Subaru seatbelt alarm, you must get into the car and close the entire door.
  2. The next step is to turn on the ignition by putting in the key.
  3. Switch the car on, but the car engine should not be powered on, or the push-to-start button may be pressed twice.
  4. Within half a minute, hook and unhook the seatbelt in a row twenty times. The seatbelt alarm should be turned off now.

How to Turn Off Seatbelt Alarm on Jeep Liberty

The seatbelt’s alarm for this Jeep repeatedly beeps when you do not fasten your seatbelt while driving. This kind of seatbelt produced by the manufacturers is known as the “Enhanced Seatbelt Use Reminder System”

The steps to turn off the seatbelt’s alarm are contained in the user’s manual, although the manufacturers advise that the alarm should not be disabled. The steps are:

Step 1: Get in the car and close the doors. Do not switch on the ignition yet but just put in the key.

Step 2: Fasten the seatbelt; the key should now be turned to the right twice; by so doing, the car engine will remain off.

Step 3: On close monitoring, a little light with a small image of a man putting on a seatbelt should appear on the side of the instrument cluster. Pause until this is cleared.

Step 4: unhook and hook the car’s seatbelt severally in a matter of seconds; then, the ignition should be switched off. As an indication that the seatbelt’s alarm has been deactivated, a sound would come out from the alarm.

How to Turn Off Seatbelt Alarm on Jeep Liberty

Frequently Asked Questions – How to Turn Off Seatbelt Alarm

Can you turn off the seat belt alarm?

To turn it off, one can buy a seat belt alarm stopper from the seatbelt’s producer or at a scrap yard. In addition, to prevent the seatbelt alarm from beeping, you can purchase a detached hook that will clasp into the opening of the seatbelt; this will disable the sound.

Why is my seatbelt alarm going off when I have my seatbelt on?

The problem outlined here could be caused by one of the following, it could be a severe problem with the instrument panel cluster (IPC) or the sensing and diagnostic module (SDM). On the other hand, the issue could be as easy as the seatbelt’s knob positioned in the seatbelt’s clamp on your right hip or the clamp’s connector, which is positioned under the seatbelt.

Where is the seatbelt sensor located?

Usually, the sensors of car seatbelts are positioned beneath the driver’s and front passenger’s seat, precisely at the seatbelt clamps.

Conclusion – How to Turn Off Seatbelt Alarm

Always buckle the safety belt while driving, hence the need for the seatbelt’s alarm to always remind the users to buckle up. However, if one needs to deactivate it, this could be done by buying an alarm stopper or by simply following instructions contained in the user’s manual.

The steps in most cars are similar; you can either deactivate the alarm by taking it to the seller’s automobile shop or simply deactivating it at home. However, it’s important to note that driving without fastening the seatbelt is not ideal; therefore, the alarm should only be deactivated if it locks up.

Scott Greene is a seasoned automotive technician for over 5 years and has been deep into advanced automotive diagnostics for a couple of years. He Loves writing about Automotive Diagnostics and Repair, Trouble codes, Buyer guides for various car parts and accessories, and lots more. 

Leave a Comment